Household Electric Appliances,Smart Home Appliances,Small Household Appliances Ningbo Shuangtuo International Trade Co., Ltd. , https://www.nbst-sports.com
Before the high-speed rotary tabletting machine installation method <br> <br> die die apparatus must first remove the hopper, add flour, a frame feeder, and other parts, and the dial face, and a die-by-die holes of the mounting member Clean and prepare, follow the steps below to install.
(1) Medium-mold device: the medium-molded fastening screws on the turntable are made one by one with the outer circle area of ​​the turntable. Do not let the middle mold fit into the head of the screw. The medium-mold device is very tight. Flat, you can use the middle die to hit the bar (random tool), then punch through the punch, for the hammer to gently enter, the middle die into the die. The plane of the hole shall not be higher than the plane of the turntable, and then the screw is fastened.
(2) Overshooting device: The tongue of the upper rail plate should be inserted into the tongue, and the vegetable oil should be applied to the tail of the middle rod. Insert the piece into the hole one by one, and rotate the punch with the thumb and forefinger to check that the head enters the middle mold. And the rotation is flexible, and no hard rubbing is required. After all the fittings, the tongue should be pulled down.
(3) Undershooting device: Pull the small door on the main body and install it from the round hole of the main body. The loading method is the same as the upper punching. After the loading, the wafer must be flattened.
(4) After the dies are fully assembled, the removed parts are installed in the original position, and the test wheel is rotated by hand, so that the turntable rotates 1-2 turns, and the upper and lower punches enter the middle die hole and act on the curve guide. Must be flexible, no collision and hard rubbing, start the motor, make the empty car run for 2-3 minutes, and put it into production smoothly and normally.
Instructions for use of high-speed rotary tablet press 1. Repeatedly check the quality of the die before use, whether there are missing edges, cracks, deformation and looseness, and whether the device is intact and good.
2. Check whether the powder of the granular material is dry and the powder content in the granules is not more than 10%. If it is not qualified, do not press hard, otherwise it will affect the normal operation and service life of the machine and the loss of raw materials.
3. For the first test run, place the indicator needle controlled by the pressure regulator on the 6th, pour the powder into the bucket, turn the test wheel by hand, adjust the filling and pressure, and gradually increase the weight and hardness of the tablet. Finished product requirements, then start the motor, then open the clutch, for the official operation of production, in the production process, the quality of the tablet must be checked regularly, whether it meets the requirements, if necessary, adjust.
4. The choice of speed has a direct impact on the service life of the machine. Due to the intrinsic viscosity of the material and the size and pressure of the material, the structure of the machine can not be uniformly defined. The structure of the machine has a stepless speed change device, which is suitable for suppressing minerals at a slow speed. Plant grass, large diameter, poor viscosity, etc. and materials that are difficult to form quickly. Quickly suitable for press bonding, good slip and easy to form materials. Therefore, the user must be determined according to the actual situation.
5. The management personnel must be familiar with the technical performance of the machine, the internal structure, the use principle of the control mechanism and the work place during the operation, to prevent damage to the machine parts, so as to ensure safe production.
6, in the use should always pay attention to whether the machine sound is normal, in case of screams and strange sounds to stop the inspection to eliminate, do not use barely.
High-speed rotary tablet press parts lubrication 1. The general machine parts of the machine are lubricated. The outer parts of the machine parts are equipped with oil cups and grease nipples. According to the type of oil cups, they should be marked with butter and oil respectively. Before driving, they should be used. All refueling once, in the middle can be added according to the temperature rise and operation of each bearing.
2. The glass oil cup on the upper cover is used to lubricate the turntable and the bearing, and 2-4 drops per minute during operation.
3. The screw cap oil cup on the worm is a lubricating worm worm gear, which is added according to the actual lubrication condition during operation.
4. The two ends of the drive shaft are equipped with rolling bearings. The shaft shell is equipped with a grease nipple. It can be refueled once every two weeks and pressed with a grease gun.
5, the tail of the punch and the curved rail guide with grease lubrication, pay attention to not too much, to prevent oil from seeping into the powder and affect the quality of the tablet.
6. When refueling, be careful not to let the oil spill out of the cup, and not to flow around the machine and on the ground, because the oil can easily contaminate the material and affect the quality of the tablet.
Die for high-speed rotary tablet press and instruction manual
The high-speed rotary tablet press has high assembly precision, excellent material resistance, wear resistance, stability and reliability, and is recognized as a popular product in the country. The use of the industry has also been radiated from pharmaceutical factories to veterinary pharmaceutical factories, electronic component factories, ceramic factories, chemical raw material plants, and even mosquito-repellent factories, fish medicine feed factories, disinfectant factories, and catalyst factories. This machine can also be changed to a profiled die. Because the model has a relatively high pressure relative to other models and the tableting speed is moderate, it is welcomed by manufacturers who produce milk chips, calcium tablets, industrial and electronic shaped sheets.